Instructions for Model No. D285
|
You Will Need l 2 x LR6(AA)
alkaline batteries for the Door-Chime. We recommend that only long-life alkaline
batteries are used. This product will not work with NiCd rechargeable batteries.
Please note: positioning
the Door Chime (or a Bell Push) on or near metal structures or reinforced PVCµ
doors or door frames may reduce the transmission range. Remove the battery
compartment cover and insert the two LR6(AA) alkaline batteries as shown in Diagram
1. When these batteries need replacing, the Battery Low Warning Light
(A in Diagram 2) will flash every 5 seconds. The Door Chime can be free-standing
or wall mounted using the wall bracket provided. If wall mounting is preferred,
screw the bracket to the wall, Diagram 3. The Door Chime hooks onto the wall
bracket as illustrated. There is an external adapter socket (B in Diagram
2) which allows you to power the Door Chime receiver from a 220-240V mains socket
using the Friedland Libra plug-in mains adapter which can be purchased separately
(UK BRITISH STANDARD Plug Model No: D254, Euro Plug Model No: D258).
Your Door-Chime can
play a 2 note or 4 note sequence. On your Friedland Libra Bell Push you will
find a Tune Select Control similar to one of those in Diagram 4. If you require
the 2 note sequence to be played move the Control to position 1. If you require
the 4 note sequence move the Control to position 2. Please note: The
note sequence choice described above is not available when the Chime is being
used with a Libra Handheld Pager, Model Number: D268. Volume Control
The Volume Control (C in Diagram 2) enables you to adjust the volume of your
Door Chime at any time or turn it off completely. The settings are: 2. High
1. Low 0. Mute Friedland Libra products use a coding system to ensure
that they work together and that there is no interference to or from a neighbouring
Friedland wirefree product. The system code in all Libra products is
set using a series of 8 switches (D in Diagram 5). In order for your new Chime
to work with a Libra Bell Push and other Libra products, you will need to
ensure that the system codes are adjusted to be the same by following this procedure:
1. Check switches 1 to 8 in your existing Libra products. 2. Look at the position
of the switches (D in Diagram 5) in your new Chime. 3. If switches 1 to 8
are not in the same position change the switches in your new Chime to match those
in your existing products using a pen tip, as illustrated in Diagram 5.
Example: if you set switch 1 in your Bell Push to the ON position, then
you must set switch 1 in your Door Chime to the ON position. In the unlikely
event that your Door Chime rings without your Bell Push being used, it means
another Friedland wirefree product, either your own or a neighbour's, is using
the same system code as your own. You should change the system code in all
your products in the same way as described above. Movement Activated
Door Chimes Friedland Libra chimes can also be activated by a Friedland
Spectra 433MHz PIR Movement Detector/ Transmitter. All you have to do is make
sure that the PIR and Door Chime have the same system code. | |





|
Other Libra Products All Friedland Libra products are compatible
and will activate each other if the system codes are set to be the same, as described
above. For example, if you install an additional Libra Bell Push for your
back door, just ensure that you adjust the system code to be the same as your
other Bell Push and your Door Chime. | |
Caradon
Friedland guarantees this product for 3 years from the of purchase. This does
not effect your statuory rights If you require further information about Libra
products, call the Friedland helpline on 0161 432 0277 ext 888. |
Problem | Possible Cause | Solution |
Chime not sounding | Batteries may not be inserted
correctly | Check all batteries have been inserted correctly |
| Chime may be positioned out of range of the
Extender | Move your Chime closer to the Extender |
| A metallic object may be blocking the signal from the Extender | Experiment
with the location of your Chime to see if you can position it in a more
suitable place | | The battery in the Extender
may need replacing | Press the Bell Push. If Confidence Light (D) Diagram
1 does not illuminate, replace the Extender battery |
| Your Extender and Chime may have different system codes | Check
the system codes in both your Chime and Extender |
| Your volume control may be set to the mute setting | Set
volume control to position 1 or 2 | | The
Extender may not be wired correctly | Press the Bell Push. If Confidence
Light (D Diagram 1),does not illuminate, check the extender wiring. If
you are extending an existing datebattery powered Chime, swap the two
wires over at the transmitter terminals | False
activation of the Chime | Another of your own or a neighbour's wirefree
product may be using the same code | Change the system codes in both
your Extender and Chime | |
|
|