Kewtech EVSE Charge Point Testing Adapter with CP Auto Check
Loading …
Kewtech
EVSE Charge Point Testing Adapter
with CP Auto Check
EVSE Charge Point Testing Adapter
with CP Auto Check
The KEWEVA testing adapter is the market's innovative new EV charge point adapter that's simple and easy to use.
The adapter is compatible with the KT66DL and all MFT’s using standard 4mm connections with EV capabilities.
The KEWEVA testing adapter works by simulating the presence of a car so the functionality of the EV supply equipment can be tested.
There is an in-built CP auto check which means one less thing to worry about and a lower resistance design ensures
the highest quality loop measurements.
The KEWEVA couldn’t be easier to use with just a single rotary dial to control the CP status simulation: standby, ready & charging - so no confusing or unnecessary extras.
AND…uniquely, there is no awkward cable to get tangled up with when testing!
The adapter is compatible with the KT66DL and all MFT’s using standard 4mm connections with EV capabilities.
The KEWEVA testing adapter works by simulating the presence of a car so the functionality of the EV supply equipment can be tested.
There is an in-built CP auto check which means one less thing to worry about and a lower resistance design ensures
the highest quality loop measurements.
The KEWEVA couldn’t be easier to use with just a single rotary dial to control the CP status simulation: standby, ready & charging - so no confusing or unnecessary extras.
AND…uniquely, there is no awkward cable to get tangled up with when testing!
- Enables testing of EV charging points
- Works with any MFT with EV charging point testing capabilities
- No awkward cable to negotiate when testing – plugs straight into the charging unit
- Automatic single dial operation for ease of use
- Direct low resistance connections for highly accurate results
- Uses standard 4mm connectors rated at 10A for testing purposes
- Red LEDs indicate live status per phase
- Single rotary dial controls the CP status simulation:
standby, ready & charging
- Separate RED LED indicates when voltage is applied to output connectors
- Auto check of 1kHz control pilot signal - no oscilloscope required
- Incorporates an IEC 62196-2 type 2 connector for EV charging units
- LED indication of Phases
- Type 2 male connector for EVSE connection
- Suitable for single & three phase charging equipment
- Smallest in class
- Supplied with durable carry case
Technical:KTKEWEVA Datasheet - 130kb pdf KTKEWEVA Instructions - 520kb pdf |
|
Product Code
Description
|
Price (ex VAT)
Price (inc VAT)
Quantity
|
|---|---|
Calibration Check Box
Loading …
Kewtech
Calibration Check Box
Calibration Check Box
Checks any make of Insulation/Continuity, Loop, RCD and Multifunction Testers
The Kewtech FC2000 provides a quick and simple method of checking the accuracy of electrical installation test instruments. It does not replace the calibration requirements but provides a ready check on instrument accuracy helping to minimise incorrect certification and costly revisits to confirm installation compliance.
The FC2000 provides accuracy checks for test instruments used to measure:
- Continuity
- Insulation resistance
- Earth fault loop impedance
- Operation of Residual Current Devices
Easy to use - just plug the FC2000 into the mains then plug in your tester.
The Kewtech FC2000 provides a quick and simple method of checking the accuracy of electrical installation test instruments. It does not replace the calibration requirements but provides a ready check on instrument accuracy helping to minimise incorrect certification and costly revisits to confirm installation compliance.
The FC2000 provides accuracy checks for test instruments used to measure:
- Continuity
- Insulation resistance
- Earth fault loop impedance
- Operation of Residual Current Devices
Easy to use - just plug the FC2000 into the mains then plug in your tester.
- Covers all your 18th Edition testing requirements
- Checks all leading makes of 18th Edition testers
- Continually validate your instruments through regular self-checking
- 12 comprehensive test points covering Loop/RCD and Insulation/Continuity
- Null facility to remove lead resistance
- Easy to use
- Tough, drop-proof, watertight case
- Comes ready calibrated
Technical:KTFC2000 Instructions - 600kb pdf |
|
Product Code
Description
|
Price (ex VAT)
Price (inc VAT)
Quantity
|
|---|---|
